- Categories
- Multi-copter Set
- Multi-copter controller
- Multi-copter Frame Kit
- Multi-copter Propeller
- Multi-coper Cam Gimbal
- Multi-copter ESC
- Multi-copter Motor
- DIY Accessory
- Spare Parts
- FPV Wireless System
- Flybarless/Gyro system
- RC Airplane
- RC Helicopter
- Helicopter Blades
- Plane Blades/Propeller
- RC Boat
- RC Car
- Servo
- Battery
- Radio Control System
- Balance Charger
- Wire/Line/Silicone Wire
- 3K Carbon Fiber
- Photography Equipment
- Screws/Nuts/Washer
- Adhesive Tapes
Recently Viewed
- Home
- FPV Wireless System
- FPV OSD system
- FPV Remzibi OSD + GPS + TTL Cable Module for APM / MWC / ARKBIRD / Rabbit / Pirate
- Description
- Shipping Methods
-
FPV Remzibi Poor Man's OSD + GPS for APM/MWC/ARKBIRD/Rabbit/Pirate + TTL Cable ModuleTechnical Data of FPV Remzibi Poor Man's OSD :- Supply power requirement: 7V-14V (ie: 2S or 3S Lipo)- Video voltage measurment range 0-15V- Engine(ENG) voltage measurment range 0-30V- General purpose ADC measurment - Build your own or use off the shelf components for many advanced readings - ie. Temperature, Amps, Air Speed, Prop Speed, RSSI, etc.- Video signals - standard PAL or NTSC- GPS - any GPS 5V supply with NMEA protocol with TLL standard TX RX signals (however best results and advantages are with dedicated GPS module working 5Hz update position)- Weight : 42 gram- Printed OSD board size 39mm x 54mmFeatures of FPV Remzibi Poor Man's OSD:- PC connection for configuration/calibration purposes using dedicated PC program- No need for a free channel on your receiver for OSD to function- GPS detection and configuration automaticaly- Home autosave function configurable based on number of satelites - button "save home" works independently- Metric(km/h) or feet(MPH) units - configurable- Zero altitude to airfield level - configurable- Fully configurable screen layout (no more cropped off data around the screen border like some other OSD's)- Graphical symbols and fonts configurable (Font editor for creating your own symbols and characters)- Voltages calibration function and all ADC inputs including alarms- Frequency calibration for Hz or RPM (gain definable)- PC configuration software includes GPS emulator for testing and setup purposes.- Language Editor - Currently available in English, Polish and French. Simple to use langauge editor can be used to translate to any other language.Button function:- Save home position (short click)- Video mode change (NTSC or PAL) press and hold button for about 1 second- Programming mode (pressed when conecting to power) for PC communicationFeatures of GPS:- Main chip: U-BLOX could modify and solidify baud rate- Locating function: <2.5m[Autonomous][50%]- Speed rate: <0.1m/s; direction: <0.5Degrees- Timing accuracy: 30ns- Reference coordinate system: WGS-84- Max. altitude: 50000m- Max. speed: 500m/s- Acceleration: <4g- Cold start: 32s in average- Warm start: 32s in average- Hot start: 1s in average- Operation temperature: -40 to +85- Wide voltage range: Main power: +3.3V~+5.5V, RTC power- Location update: 1Hz~5Hz(default 5Hz,200ms)- Data rate: 9600bps~ 115200 bps (default 38400 bps)Package Included:- 1 x Remzibi OSD main chip- 1 x TTL cable(93cm)- 1 x GPS Module- 1 x Reflection board- 1 x Support rod- 1 x M3 screw- 1 x Output cable For GOPRO HERO3(23.3cm)- 1 x Output cable For GOPRO HERO2(42cm)- 1 x Output cable For Video signal(31.5cm)- 1 x cable For GPS out (30.5cm)
Write Your Reviews
Tell us what you think about this item, share your opinion with other people. Please make sure that your review focus on this item. All the reviews are moderated and will be reviewed within two business days. Inappropriate reviews will not be posted.
Have any question or inquire for this item? Please contact Customer Service. (Our customer representative will get back shortly.)
Have any question or inquire for this item? Please contact Customer Service. (Our customer representative will get back shortly.)
