High-frequency head MAT - NF6 DSM2 compatible with Futaba, Walkera, Wfly MCPX

Are you in for the damage of aircraft broke the original receiving distress?

Are you still more for the plane to buy more the higher cost of the original receiver bitter brain?

You still use the old remote control, Is hesitant to replace it?

NF6 dsm2 high-frequency head to solve these troubles!

 Model : New MAT - NF6 DSM2 high-frequency head manual compatible with 6 channels

Power supply: built-in 3.7 V lithium battery.

Wireless power: <= 20 DBM.
The average working current: 65 ma.

Dimensions: 25 × 40mm

Net Weight: 45g.

-

function

1. Compatible Spektrum, Futaba, Graupner/SJ MZ - 24, Hitec, Walkera, heaven and earth to fly, Flysky, farce, kay Frsky many remote control;
2. Compatible with DSM2 system receiver (6) within channel;Support most remote control horizon HorizonHobby released with DSM2 receiver products (such as: MCPX, UMX triaxial fixed wing aircraft, etc.);
And FUTABA 3. The FUTABA remote control of the remote control channel order the same transmitter channel order, intelligence into type A transmitter channel order, the use of convenient DSM2 receiver.
4. The receiver channel order fixed into the accelerator, aileron, elevator, direction, landing gear, AUX, make the tactile DSM2 receiver can normal open it.
5. Support the transmitter channel order:
F. a. types: throttle, aileron, elevator, direction, landing gear, AUX
G. B type: aileron, lift, throttle, direction, landing gear, AUX
8. A distance function, USB rechargeable connected to computers.Easy operation, simple installation, has small volume, light weight.

The LED state that

State of the LED          A red light                 Blue light         
Long bright               The normal work         The battery is normal
flashing                The frequency, range      Low battery, charging mode
 

Installation method
1. Put a piece of Velcro in the back of the remote control, and then stick instead of Velcro on the back of the NF6, NF6 fixed on the back of the remote control.
2. Insert signal simulator of the remote control interface, if the simulator of the remote control interface is not audio, you need to use interface.
Method of use
1. The frequency of the transmitter to adjust to PPM mode.First insert the line frequency DSM2 receiver frequency on foot, on DSM2 receiver with electricity, DSM2 indicator lights flashing.Then hold down the NF6 BIND switch, at the same time ensure that the remote control throttle channel is the lowest position, will NF6 power switch to "ON", when NF6 red LED indicator light will start flashing.Observe DSM2 receiver status lights until state, light long on the end of the frequency.Unplug DSM2 high frequency to frequency line, again with electricity, can be normal use.
2. Ranging in normal use, according to BIND button 2 seconds long, into the distance mode, high-frequency head red LED indicator lights flashing.Distance measurement mode, if DSM2 receiver function that can be received within 10 m distance signals, is working properly.Again according to the high frequency head button 2 seconds long, the red LED indicator long on, is out of range model, into the normal working mode.
3. The normal use of computer, to ensure that the remote control throttle channel is the lowest position, or high frequency head won't start.Especially the FUTABA factory Settings control throttle channel is reverse, users need to dispatch the gas channel is.After startup, observe state of red leds, red LED long bright just said high-frequency head work.
4. The charging NF6 received on the computer with USB cable or 5 v ac adapter can charge.Need charge when the signal from the remote control.After the blue LED flashing charging time, full of blue LED grow light.
Common problems to deal with
1. After power on high-frequency tuner does not work
Will play to the lowest position, the throttle rocker NF6 high-frequency head will start automatically.
2. The FUTABA control, sequence and different transmission channel order receiver over there?
NF6 high-frequency head, input channel order, will be automatically converted into the channel order JR.Doing so has two advantages, first is to ensure that the first channel is the accelerator, such a DSM2 receiver is out of control protection.The second advantage is that playing similar MCPX class with a built-in receiver plane, don't have to adjust the control channel order on it.
3. The transmitter channel order is neither FUTABA type, nor JR type, how to do?
NF6 high-frequency head temporarily only supports the FUTABA and JR transmitter channel order.
 
Accessories list
NF6 high-frequency head take an audio line.
A 2.4 G antenna.
USB charging line one.
A magic stick.
A manual.
Note: the FUTABA, fly remote control such as heaven and earth are subject to purchase extension cord